Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
Just how do you actually feel about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably tough job. If the old tub is readily obtainable, the job can move quickly; if you need to open up a wall surface to get rid of the old bathtub as well as position the new bathtub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will require a helper to leave the old tub as well as set in the new one. Ensure you have qualified yourself for the job and fit trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your restroom if you have actually currently gotten a new tub and do not require to alter the plan of your previous water supply pipes.
Your devices as well as material checklist need to consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be fairly troublesome due to the restricted accessibility that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin guaranteeing that the washing machines are in area between the tap and also the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are handy in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the tub up until the level reviews level.
To install taps, fit all-time low of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leaks as well as tighten them if required. Fill up the tub and also check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub needs to wait till the bath tub has actually been utilized a minimum of once as this will certainly settle it into its final placement.
Planning for the Installment
First of all, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, triggering the water to pass through the wall surface between the bath and the tiling, causing difficulties with dampness as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can split rather very early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very involved in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I'm hoping you liked my article. In case you enjoyed our page if you please remember to pass it around. We appreciate reading our article about Installing A Bathtub.
Course Detail Report this page